how to make a lanyard keychain with 2 strings

Aug 15, - Guide 3 in my lanyard series The Double Spiral Lanyard. Pick out three colors of Craft Lace. Fold your lace in half. Put one string on the bottom and two on the top. Mar 13, †Ј To make one lanyard you'll need: two 2 1/8" x 40" strips of fabric (one of each print) one " x 2" strip (there's two in the picture but you only need one) one" x 40" strip of felt, thin cotton quilt batting, or fusible fleece. one 1" swivel snap clip.

Lots of free sewing patterns and tutorials for making bags, zipper pouches, quilts, mini-quilts, easy clothing items, and other crafty little things to sew. The lanyard in this free sewing tutorial is double sided so you can use two coordinating fabrics to make it twice as nice! Of course a pretty one because the ones they try to sell you in the stores are usually just pretty sad.

Get started by pinning your two long strips right sides together along one long edge. Press the seam allowance open, and then fold the top and bottom edges to the center so they just touch the seam allowance edges. Insert the strip of felt or other stabilizer inside one of the folded sides.

It doesn't matter which side Refold the strip and pin about every 6". If the top layer of your fabric wants to pull away while you are doing this part, try holding the strap firmly about 6" in front of the presser foot as well as holding on to the strip from the back. Let your sewing machine feed the strip through evenly, but if you are holding firmly from both what does 195 65r15 mean, the top layer won't pull so much.

Trim the ends of the strap to make them clean and even. Then slip the swivel hook on. Set your stitch to the widest zig-zag you have. Form a circle with your strap by butting the ends right up against each other.

Sew a zig-zag stitch down the center. Backstitch to hold it together during the next few steps. Now take your 3. Arrange the lanyard with the swivel clip at one end near the zig-zag seam. Wrap the small strip around the seam, tucking the ends inside the lanyard. Topstitch a square over your little piece. I like to use the topstitching lines on the strap as what is rbrvs stands for for the sides of my square.

Be sure to neatly backstitch so this part holds. And you're done! Be sure to post pictures of your lanyards on Instagram and tag me sewcanshe so I can see them! A walking foot also works great on straps like this. Happy Sewing! How to Make a Kisses Quilt Pattern - free jelly roll quilt pattern! Free DIY Tips.

Introduction: Lanyard Weaves

Jul 12, †Ј With 1 yard of lace, you can make about a 4 inch keychain in the square pattern. LetТs move on to the ROUND weaving. After mastering the square boondoggle, try the round. It starts with the exact same 2 strand weave from the beginning. Fold your cord in half, then make a loop with the right strand. Twist it in a clockwise direction to get the loop facing the right. Feed the left cord through the loop, under-over. Pass the left cord over the right. Mar 17, †Ј First, you have to lay out your string. I recommend about a foot or two of each color (or do both the same color) on the first lanyard. This will make a keychain-sized lanyard. Cut one string, then measure it against the other for length.

Lanyards are great. They can be woven into many shapes, sizes, and colors. They can be used as keychains, ID badge holders, lamp pull-cords, bracelets, replacement zipper pulls, and just about anything else. So much can be done with lanyards, I'm surprised more people don't love them. To weave or tie lanyards, you need three things: 1. Lanyard string. This comes in a variety of colors, usually in yard spools.

Any brand will work. A ring. Any sort will do. You can make a lanyard without one without any problem, but if you omit one at the beginning, you will NEVER be able to get it on at the end if you change your mind. Lanyards sometimes take awhile. Shorter ones can be done in an hour, while longer ones could take several. Start with a short one till you get the hang of it and are sure you wont give up halfway through.

The first knot is unquestionably the hardest one. All of the other knots could be done in your sleep compared to this one. It is very hard to describe, so please look at the pictures as I walk you through it. I know there are other Instructables on 'lanyards,' but all of them that I have seen use paracord, which is woven differently.

It is neither better nor worse than Rexlace, just different. First, you have to lay out your string. I recommend about a foot or two of each color or do both the same color on the first lanyard. This will make a keychain-sized lanyard. Cut one string, then measure it against the other for length. Lay them out in an X fashion. Now imagine they are coming not from a common center but from the four sides of a square.

Look at my edited picture. Take the one on the top right and move it down. Follow with the one on the right bottom. Now the bottom left. Finally, take the string on the left top and pass it over the first string, but under the second. You should now have four strings, each going over one string and under the second. Pull this tight against the ring. Now that the first knot is done, you truly have a warped square.

It should be much easier to put the knots together. Simply do the same thing over again, laying each string down to form the same pattern. Make sure to bring each string straight across or it won't look right. The first two or three knots will probably look bad, but ignore it.

One notice: Beware of twists! I cannot stress this enough. If the string is twisted, it will interrupt the symmetry and the lanyard will look odd.

Even the most experienced people sometimes find themselves backing up a few knots to straighten out a twist. The best way to avoid this is to make sure you never have them.

Continue making knots until there are of them. Now that you have a few knots, you should be able to hold your lanyard easily. This is the fun part of lanyards. Depending on the length of string you cut in the beginning, you can spend as little as twenty minutes or many many hours putting knots together.

It is a great way to pass the time, completely safe, and the results are very impressive. As you become more experienced, you can do many tricks and twists to make a more interesting lanyard, and I might make another Instructable about these later.

For now, keep working until you have only about inches of lace left. Finally, we finish off the lanyard to keep it from untying. This is done with something called a Turk's Head knot. Again, this is a complicated step, so refer to the pictures. To tie it, first complete one more lanyard knot, but do not pull it tight. Make sure the string is on the left-hand side.

If not, tie one more knot. Take any one of the strings and run it counterclockwise past one string. Then put it under the string of the same color on the other side and bring it up through the middle. Take the string that you just went around and do the same thing. Then once more. Finally, the last string is again different to make it symmetrical. Imagine when using the last string that the first string had not been tied. Where would it go?

If you do this right, the entire lanyard will look the same from every side. Cut the strings to whatever length you like. They can be really long or practically in the knot.

It doesn't matter, just your personal aesthetics. You have completed your very own lanyard! Now go show your parents, kids, co-workers, partners, etc. I hope you enjoyed this project, and please vote for me in the contest! Remember, changing the lanyard very slightly and repeating it will give you a whole new look. Contest questions. What did you make? I made a lanyard, which seems to me a very useful alternative to string in many applications. Many things can be repaired by weaving a lanyard around them.

They are very common at camps,especially with the Boy Scouts, who love knots. I like to make these for fun, and people seem to love them, especially my little cousins and my girlfriend. How did you make it? I originally started doing these at camp, and i thought of them when I was looking for something to post that hadn't been done already. It isn't very difficult, just a little lime-consuming.

Where did you make it? I spent some time i would usually have spent playing video games or bored in class making this lanyard instead. The small ones I can do in a couple class periods, while I remember dragging some enormous ones around for a week.

This one took about 15 minutes, including the pictures. Home is a great place to do these as well, but I make most of mine on long car trips where there is nothing else to do for hours at a time. What did you learn?

In doing this project, I learned to make a useful tool for many things. Since I do these quite often, I have some experience and didn't learn much from this basic one. I have also taught several people to do them, but it is definitely much harder when I cannot help them face-to-face. I have tried doing the square weave following or trying to instructions from several other places and have always failed.

I had no trouble with yours - awwww sweet success. Thank you. Reply 1 year ago. Looks great! I hope you guys have fun doing this. I am using your square as above have 4 lines out and same length and same diameters. I'm ending up with 2 same color lines feet longer lanyards.

Help I've done this pattern for Avery long time and now this making me,waste cord. Reply 6 years ago on Step 2. Is the problem with the starting knot or the subsequent ties as you go through?

0 thoughts on “How to make a lanyard keychain with 2 strings

Add a comment

Your email will not be published. . Required fields are marked .